This is why our Baths and Showers are Stronger, Tougher and built to last.

Click here to read why our showers are the best.

The most important part of any Walk in Bath is the Frame.  It needs to be welded together, not bolted as a bolted frame will move, it must be substantial in size and a good quality. Our frames are all stainless steel and welded together.

Our frames are all stainless steel and welded together.

Some companies use a steel frame which is powder coated, This is not sufficient as the rust eats into the bare metal on the inside and also where the spring washer has worn away the powder coating as the frame was assembled.

Our stainless steel frame will prevent any rusting and ensure the rigidity and longevity of your Walk in Bath.

The next most important aspect is the Walk in Bath design. All our baths are manufactured as below.

There are THREE layers of high gloss Gelcoat. Most Walk in Baths only have one.

There are FOUR layers of high-efficiency glass-fibre used to build up the thickness of the whole body. Most Walk in Baths have only two layers.

We also thicken the main supporting areas around the corners and around the back of the seat where we use FIVE layers of high-efficiency glass-fibre and we use SIX layers in the floor area.

A lot of our competitors only use three layers of fibre-glass. In our opinion, this is insufficient.

All the Air Jet and Water Jet holes are re-enforced and we apply a section of marine ply, glass-fibre and resin re-enforced to the underside of the base.

The Stainless Steel Frame will prevent any rusting and ensure the rigidity of the Walk in Bath. Please note the hygienic bidet cutaway in the photo.

The photos show the Stainless Steel Frame, Fiberglass body, Air Manifold, Jet attachment, Blower and Stainless Steel Plate and please note the general tidiness and attention to detail of the whole system.

The Soaker models are all built to the same high standard.

As far as we are aware no other company can offer you our worldwide certificated designs and models.

A full survey will only take 90 minutes and we can ascertain that your chosen model will fit and you are on your way to a luxurious bath.

Stainless Steel Handle and Jet Locations The Air Jet_attachments

The tidyness of the Air System with the Stainless Steel Frame Underside of Bath

Why our Showers are the Best

Our shower range of 42 models with over 100 options are available to view by clicking on the Shower link on our Home Page.  As with our Walk in Baths, our walk in shower enclosures offer you the latest designs and options. Now is your chance to purchase the same type of shower and construction that are installed in the disabled bathrooms in Hotels, Universities and Care Homes.They really have to stand the test of time. The Rolls Royce of Walk-in-Showers.

Standard Features Include.

• Standard Shower, Cubicle or Pod design to include sides and rear.
• Designed to fit into your existing bath space
• No need for expensive tiling or digging into the floor.
• Adjustable extension panel to fill in the gap after removing your existing bath.
• Water control is a single-handle anti-scald valve for ease of use and safety.
• Removable handheld 3D showerhead with hose and chrome-plated slide bar.
• One 18 inch grab bar fitted to your requirements.  (More if needed)
• Removable optional chair with supporting arms.
• Possible to install in one day.
• Complete Bathroom refit service available.
• Watertight lifetime guarantee.
• Installed by fully trained qualified installers.

This is where your savings come in.  As there is no tiling involved, no need to cut into the floor to run the waste and no need to replace the U bend and associate pipe work, we can normally fit our showers in ONE day. If a pump is required it may be two

No other company can offer you our design and models.

A full survey will only take 90 minutes and we can ascertain that your chosen model will fit and you are on your way to a luxurious shower.

Save

Save